We are officially in the thick of the e-dirt bike build! In Episode 3, the bike starts looking like a real machine. I’m tackling the motor installation, custom part fabrication, and a deep dive into the 2-stage jackshaft transmission logic.
In this episode
Fabrication & Prep: Creating motor mounting plate and battery supports from 1/8" pickled steel.
The Powerplant: Installing the 10kW motor from Golden Motor and explaining the bolt-on mounting strategy for future upgrades.
Precision CNC Work: Using the Makera Carvera Air and Genmitsu ProVer XL to machine custom axle blocks, battery brackets, keyways and sprockets.
The Transmission: Building a custom 2-stage chain driven jackshaft system. I break down why I chose the 6.6:1 gear ratio and a 520 O-ring chain over a belt for this trail machine.
Weight Check: We’re currently sitting at ~150lbs. Can we keep the final build under 200lbs?
Featured in this video
Motor: Golden Motor HPM-10KW 72V
Battery Cells: Molicel 21700 P42A
Stay tuned for the next video in just a few days, where I do a deep dive into how I design and DIY my own sprockets. After that, we start the 72V 50Ah battery build for this bike!
Missed the earlier episodes? Watch the full playlist here
Specs
Motor: Golden Motor HPM 10kW continuous / 20kWp dual stator PMSM
Controller: EZ-B72800 sinewave, 72V, 800A phase / 400A battery current
Transmission: 2-stage, 6.6:1 gear ratio, ~330Nm torque at the wheel
Battery: 72V lithium pack (planned ~4kWh, 100km range)
Suspension: 790mm adjustable forks + 330mm rear shock w/ progressive linkage
Wheels: 19” front & 18" rear, ~12” ground clearance
Target curb weight: ~190 lbs
Top speed: ~75 km/h
#ElectricDirtBike #EVBuild #Fabrication #MotorcycleBuild #GoldenMotor #CustomChassis #LaserWelding #DIYMotorcycle #ElectricMotorcycle #MetalFabrication #3DPrinting #TubeBending #Welding #CNC
In this episode
Fabrication & Prep: Creating motor mounting plate and battery supports from 1/8" pickled steel.
The Powerplant: Installing the 10kW motor from Golden Motor and explaining the bolt-on mounting strategy for future upgrades.
Precision CNC Work: Using the Makera Carvera Air and Genmitsu ProVer XL to machine custom axle blocks, battery brackets, keyways and sprockets.
The Transmission: Building a custom 2-stage chain driven jackshaft system. I break down why I chose the 6.6:1 gear ratio and a 520 O-ring chain over a belt for this trail machine.
Weight Check: We’re currently sitting at ~150lbs. Can we keep the final build under 200lbs?
Featured in this video
Motor: Golden Motor HPM-10KW 72V
Battery Cells: Molicel 21700 P42A
Stay tuned for the next video in just a few days, where I do a deep dive into how I design and DIY my own sprockets. After that, we start the 72V 50Ah battery build for this bike!
Missed the earlier episodes? Watch the full playlist here
Specs
Motor: Golden Motor HPM 10kW continuous / 20kWp dual stator PMSM
Controller: EZ-B72800 sinewave, 72V, 800A phase / 400A battery current
Transmission: 2-stage, 6.6:1 gear ratio, ~330Nm torque at the wheel
Battery: 72V lithium pack (planned ~4kWh, 100km range)
Suspension: 790mm adjustable forks + 330mm rear shock w/ progressive linkage
Wheels: 19” front & 18" rear, ~12” ground clearance
Target curb weight: ~190 lbs
Top speed: ~75 km/h
#ElectricDirtBike #EVBuild #Fabrication #MotorcycleBuild #GoldenMotor #CustomChassis #LaserWelding #DIYMotorcycle #ElectricMotorcycle #MetalFabrication #3DPrinting #TubeBending #Welding #CNC
This website uses cookies
Comments 0
Be the first to comment!