Andy Huot Creations Andy Huot Creations
May 13, 2026

This DIY Submarine Took Months to Engineer—Here's How

Back in fall of '23, I set out to create an ROV submersible, resulting in what has become a fully functional underwater robot. This video details the design process, including control diagrams and 3D...

Back in fall of '23, I set out to create an ROV submersible, resulting in what has become a fully functional underwater robot. This video details the design process, including control diagrams and 3D modeling, as well as the physical components and underwater testing of this DIY underwater drone. See how this underwater drone was brought to life!

Download Link

Printables Store

Syringe for Ballasts
Serial Wombat I/O ExpanderS
NRF24 2.4G Transceceiver Module
ESP32 for ROV Control
Arduino Nano for Controller Display
PCA9685 PWM Servo Driver
BNO055 IMU
ADS1115 ADC
Protoboard I used for main circuit board
Hookup Wire for Protoboard
Dupont Connector Kit for Terminating Cables
Ballast Motor Driver
Ballast Limit Switches
Magnets for Sensors
JSN-SR04T Ultrasonic Sensors
AT10II Radio Controller
Radio Controller Battery
Nextion Display for Telemetry Data
Servo Twisted Extension Cable
SMA Extension Cable for Antennas
Pigtails to Hub from RadioLink
SMA Adapters for Hub
FPV Camera Receiver and Monitor
FPV Camera Transmitter;
FPV Camera
Switch for Camera LED Ring(what I’d use today)
100 RPM 12V Gear Motor for Ballast Control
Underwater Thruster for Propulsion
INA219 Current Sensor for Battery Usage and Current
Bidirectional ESC for Thruster Control
Servo Horn for Thruster Mounting
Rod End for Flaps Servos
Servos for Flaps
Y Harness for Servos
Servos for Thrusters
16 Amp Terminal Block for Power Distribution
Waterproof Grease (get the 3 pack)
Magnet-o-Pot Linear Potentiometer for Ballasts
5” Clear PVC Pipe x 50”
Acrylic Dome for Camera
Zip Ties for Core
Battery for ROV
M3 Heat-Set Inserts
M4 Heat-Set Inserts
M5 Heat-Set Inserts
M6 Heat-Set Inserts
10 Pin Terminal Block Connector
M3 x 180mm Threaded Rod
M10 Nylon Lock Nuts
M10 Coupling for Weight Balance
M10 Cap Nut
M20 Tap
M12 Tap
Metric Flat Head Screw Set
M3 Screw Set
M3 SHCS Screw Set
Ballast Lead Screw and Nut
Ballast Bearing
M3 Threaded Rod
¼” ABS Rod for Dowels.
M3 Threaded Rod
M3 Threaded Rod
M3 Nylon Lock Nut
M3 Washers
3mm Sleeve Bearing for Flaps
M5 Nylon Lock Nut
Nylone M5 Hex Nut for Core Assembly
M5 Threaded Rod for Wings
M6 Screws for Bulkhead
M6 Thumb Screws for Battery Compartment
Metric Set Screw Kit
Metric Tap Set
Sanding Sticks
Sanding Sticks
Sanding Sponges
Paint I used for parts outside of hull
Potting Epoxy I used for waterproofing electronics
PETG (What I used for everything I printed, except the bulkheads, and battery compartment blocks)
What I would use to print bulkheads and battery compartment blocks
134

Comments 0

Replying to
5000 max

Be the first to comment!

This website uses cookies
This website uses cookies.
To maintain our services, we use cookies. They allow us to personalize ads, analyze our traffic, and provide social media features.

Customize your preferences

Select the cookies you accept: